4 Must-Have Handsaws: Dovetail, Backsaw, Dozuki, and Coping

Synopsis: If you are not regularly using handsaws in your shop, you may be missing out on the best tool for a number of jobs. There’s nothing better for crosscutting delicate moldings, or getting into tight spaces like dovetails. There’s nothing safer for trimming pegs flush. Equip your shop with a dovetail saw, a backsaw set up for crosscuts, a dozuki, and a coping saw, and then learn how to get the best from each one.

I regularly use four handsaws in my shop, not because I’m a hand-tool nut but because a handsaw is often the smartest, most efficient choice for the job at hand. Take the job of crosscutting or mitering delicate moldings and miter keys. You could do those tasks at the tablesaw or miter saw, but you’d need to devise a jig to hold the workpiece during the cut, and there’s no guarantee that the spinning blade won’t chew up the workpiece. It’s much quicker, safer, and cleaner to make the cut with a backsaw.

Handsaws are great for getting into tight spaces, too. A coping saw is the perfect tool to cut out the waste between dovetails. The thin blade can fit into even the tightest pin socket and make a turn along the baseline, removing the waste in seconds. Chopping out waste with a chisel takes much longer, and routing it out is possible only when there’s enough clearance between the tails to fit the bit.

And then there are jobs that a power tool simply couldn’t (or shouldn’t) do, like cutting pegs flush. The only power-tool option is a router, and you have to make an auxiliary base to raise the router and then dial in the bit’s cut depth so that it doesn’t ruin the surface. Not to mention that pegs are often used on narrow parts, like legs, where the router can tip and ruin the part.

There are lots of handsaws out there, but I think the four you need most are a dovetail saw, a backsaw set up for crosscuts, a dozuki, and a coping saw. I’ll show you some tips on getting the best from each one.

1. Dovetail saw

I bought my dovetail saw to make handcut dovetails, but over the years I’ve found that it’s good for other tasks, too, such as notching a shelf or drawer divider to fit in a stopped dado cut in a case side. For a smooth cut, I’d recommend a saw with about 19 teeth per inch (tpi), sharpened for a ripcut. Western-style saws cut on the push stroke and come with two different handle styles—pistol grip or straight. I prefer a pistol-grip handle, which makes it easier to push the saw and control the cut.

2. Crosscut saw

When you’re making furniture, there are always small parts—like moldings, pulls, drawer stops, and pegs—that need to be cut to length. Instead of using a tablesaw, which could destroy those delicate parts in a flash, I use a Western-style carcass backsaw. A crosscut saw with about 12 to 14 tpi and a blade that’s a bit taller and longer than on a dovetail saw can easily make clean, accurate cuts in parts up to 1 in. thick and 3 in. to 4 in. wide. To increase accuracy, I use the saw with a sawhook, which is simply a flat board with a square fence (and a cleat that goes in your vise). The hook is great because it gives you a way to hold the workpiece still during the cut (both you and the saw press it against the fence) and helps to keep the saw cutting straight and square.

3. Dozuki

A dozuki saw has a thin, flexible blade, with fine teeth and a straight handle, which makes it well-suited to flush-cutting pegs. The flexible tip helps it get close to the base of a pin, and the straight handle is easier to hold and control with the saw on its side than a pistol grip would be. Get a crosscut dozuki with about 20 tpi. So why not just use a flush-cut saw? Their teeth have no set, so they clog and don’t cut as well. Dozukis don’t have those problems. The thin blade can kink, so get a saw with a replaceable blade.

4. Coping saw

With its thin blade and tall frame, the coping saw is adept at cutting curves. It was used in the past to cope molding to get perfect miters. But I use it when cutting dovetails. I was taught to chop out all of the waste with a chisel—a tedious job. When I tried sawing out the waste with a coping saw, it was a watershed moment for me and I’ll never go back. You don’t need a super-expensive frame, but don’t go with a hardware store cheapy, either. I spent about $20 on mine and it’s easy to tighten and adjust the blade. The handle is comfortable, too. As for blades, get ones with a fine cut. They cut slower, which means the saw is less likely to jump the kerf at the end of the cut and damage the tail or pin.

From Fine Woodworking #231

To view the entire article, please click the View PDF button below:

Fine Woodworking Recommended Products

Veritas Precision Square

This precision square is incredibly versatile, from checking squareness to dialing in machine setups.

Buy at Lee Valley

Suizan Japanese Pull Saw

A versatile saw that can be used for anything from kumiko to dovetails. Mike Pekovich recommends them as a woodworker's first handsaw.

Buy at Amazon

Lie-Nielsen No. 102 Low Angle Block Plane

With smooth, precise adjustments and wonderful balance, this compact block plane is a joy to use. It doesn’t have any bells and whistles, but there’s not a better block plane available for the money.

Buy at Direct