Three Planes for Cutting Rabbets

I have two favorite ways to make backboards: shiplap joints and tongue-and-groove joints*.

For shiplap joints – a series of mating rabbets – there are several handplane options, and students typically already own at least one of the three I favor: a straight rabbet, a shoulder plane, or a skew rabbet/moving fillister (as shown at the top of this post).

Skew rabbet plane

Of the ones shown above, the Veritas skew rabbet plane is by far the fastest. (And because it has a nicker, depth stop, and movable fence, it is technically a moving fillister plane – a plane designed to be used both with and across the grain.) But it can be tricky for beginners to cut a 90° rabbet with this plane; it’s all too easy to tip it off the work a little bit, and end up with a sloped rabbet. I’ve found that the knob on the front exacerbates this tendency; that’s why I confiscate them. (Someday, I’ll make a coat rack out of the many I’ve acquired.)

But with a little practice, it’s quick and easy. Set the depth stop to a hair more than half the thickness of the workpiece, and set the fence to the width of the rabbet you want to cut. (I usually aim for about 3/8 in. or a little more on backboards, depending on the size of the project.) Cinch down tight on both. I use nylon-jawed pliers to tighten the knobs.

Each hand has one job: The right hand pushes (this is for a right-handed plane; the skew rabbet is also available as a left-handed plane, to use in the other direction), and does so without grasping the handle too hard (which can make the plane wobble). The left hand holds the plane firmly at 90° to the work, with fingers pressing the plane’s fence into the work and the thumb pressing down (right where the knob used to be).

Start at the near end of the board and pull back a few inches, then take a short stroke, repeat with a slightly longer stroke, and again, working your way back until you’ve established the full length of the rabbet. A few short strokes to establish the shoulder are easier to get right than one long stroke. Why pull back? It’s mostly habit: When cutting across the grain with this plane, drop the nicker to score the shoulder as you pull back to effect a cleaner cut. (Lie-Nielsen makes a skew rabbeting block plane, the No. 140, which is not a moving fillister plane – no depth stop.)

Work your way down to final depth and width; the fence and depth stop will tell you when you’re done. Then check the rabbet to make sure it’s square, especially if you’re new to this method. (And if you’re not, a few strokes holding the plane at 90° will hopefully solve the problem – plus you’ll know where to concentrate your attention on the next cut.)

Straight rabbet plane

Another fast, and almost always successful method for those new to hand tools, is to use a straight rabbet plane against a fence. The only tricky thing is to keep an eye on the baseline, and stop cutting when you reach it.

Mark the depth and width of the rabbet with a marking gauge, then clamp a long, straight piece of scrap at the marked line on the top. Again, each hand has a specific job – much the same as above (except a straight rabbet can be used with either hand as the dominant hand). The dominant hand pushes, the off hand pushes in and down. Again, work your way back to establish the full length of the rabbet. And again, check your work.

Shoulder plane

I do not like using a shoulder plane to cut rabbets. This plane is designed for precision work, and as such takes only fine cuts. So it takes (comparatively) forever to cut rabbets with it. What it has going for it, however, is its sharp arris, which can assist in making this cut.

Establish the shoulder and depth with a marking gauge, and be sure to cut that shoulder line deep. Carefully now, put the corner of the shoulder plane into that cut line at an angle, then make a cut – still at an angle – all the way down the workpiece. Repeat a few times, each time bringing the plane closer to level. You are establishing a V-cut shoulder.

After the V-cut is deep enough to register the plane against it at 90°, finish the cut at 90°, pressing the plane into the shoulder.

Yes, I could use this method with my straight rabbet plane, too – but it’s a little trickier because the corner of my wooden plane isn’t as sharp as that on my metal shoulder plane.

What about a rabbeting block plane or rabbeting jack plane? Well, I don’t really like planes that are meant to do multiple jobs…and I always cut myself when using a rabbeting block plane as a “regular” block plane. But more important than my clumsiness is that it’s fairly easy to flex the sole of these planes by tightening the lever cap too much. (The same is true on shoulder planes – but you’d have to severely over-tighten to flex the sole on that plane).

*I’ll cover my favorite way of creating a tongue-and-groove joint in my next blog.

Handwork: Three ways to cut a rabbet joint

The rabbet joint is a useful joint to know. Here, hand-tool expert Vic Tesolin shows three ways to cut one by hand—with a rabbet plane, with a shoulder plane, and with a chisel and router plane.

Fillister Plane Cuts Quick Rabbets and More

Learn what they can do and which ones are the best

Handcut Rabbets and Dovetail Fitting

In this video workshop episode, Chris fits the dovetails together, after using a rabbet plane and shoulder plane to create the rabbets in the back of the case

Fine Woodworking Recommended Products

Leigh D4R Pro

The D4R Pro is Leigh’s flagship jig. Like the other Leigh jigs in our test, it represents a different world of quality, from its clear, comprehensive instructions to its ingenious engineering, impeccable manufacturing, and unmatched capabilities.

Buy at Amazon Buy at Woodcraft

Veritas Standard Wheel Marking Gauge

A wheel-type gauge is the easiest to use, and this wonderful Veritas model is a steal at $38.

Buy at Lee Valley

Leigh Super 18 Jig

This jig is a value-oriented alternative to the Leigh D4R, but its template system is just as excellent.

Buy at Amazon Buy at Woodcraft