Flatten Wide Boards on a Narrow Jointer

Synopsis: In most home shops, there is a mismatch between the capacity of the jointer and planer–mostly because wide jointers are expensive. Working in a shop with a 12-in planer and a 6- to 8-in. jointer limits the width of boards you can mill to the smaller size. This technique can help. The secret is a wide, shallow rabbet cut on the jointer, and a spacer that is used on the planer. Follow these instructions, and you’ll be able to stretch a 6-in. jointer’s capacity to 9 in., and an 8-in. jointer’s capacity to 12 in.

From Fine Woodworking #204

As most woodworkers know, it takes both a jointer and a thickness planer to machine a board so both faces end up truly smooth, flat, and parallel to each other. The jointer gets one face flat and the thickness planer makes the other face parallel to the first.

Ideally, the jointer and planer are the same size. But wide jointers cost a lot more than wide planers and weigh as much as 1,000 lb. So most home-shop woodworkers have a planer at least 12 in. wide, but a jointer that’s only 6 in. or 8 in. That limits the width of boards they can handle to the size of the jointer. But we’ve found a way to stretch our jointer capacity by 50%.

Some ground rules

Before starting, it’s important to keep a few things in mind that make the procedure safer and just about foolproof.
To use this technique, you’ll need to remove the jointer’s cutterhead guard because it interferes with an extrawide board during a cut. So you’ll need to make a simple guard (see facing page) that clamps to the fence of the jointer and allows a wide board to pass underneath it.

A pair of push blocks is a must. You’ll need one in each hand to feed the board.

Finally, be aware that there is a width limit. On a board that is more than 50% wider than the jointer knives, the unsupported edge could tip downward, producing a side-to-side taper. So if you have a 6-in. jointer, limit the board width to 9 in.; if you have an 8-in. jointer, the limit is 12 in. wide.

Jointer

For a second pass on the jointer, you might need a simple jig

If the first pass wasn’t enough, you may have problems making a second one. On most jointers, the infeed table is wider than the knives, and your rabbeted step will hang up on the table, tilting the board. But the solution is simple.

Use 1/4-in.-thick hardboard, medium-density fiberboard (MDF), or hardwood plywood like birch to make an auxiliary infeed table. Cut it as wide as the length of the knives (no wider or the boards will end up with the taper) and as long as the infeed table plus 3/4 in., to allow room to mount a stop block. The stop block prevents the auxiliary table from sliding forward during a cut.

To install the table, first set the jointer fence to make the widest possible cut. Then lower the infeed table to account for the auxiliary table’s 1/4-in. thickness.

Secret is a wide rabbet and a spacer

First, joint one edge of the wide board. Then position the jointer fence to make the widest possible cut and set the infeed table to remove 1⁄16 in. to 1⁄8 in. of stock—the closer to 1⁄8 in. the better, depending on how much extra thickness you have.
Next, with the jointed edge running against the fence, make a pass on one side of the board. The cut produces a wide, shallow rabbet in the board.

Hopefully, that first pass will get you a surface flat enough for the next step.

If it doesn’t, the solution is to make additional passes. To do that on most jointers, however, you’ll need to add an auxiliary table (see photos and drawings, p. 70). But if your infeed table is narrower than the knives, you can make as many additional passes as you need. Once you have a wide, flat rabbet, you can make the simple spacer (which you’ll be able to reuse). Just cut a piece of flat and straight 3⁄4-in.-thick plywood at least as wide as the rabbet, and longer than the rabbet by 1 in. or 2 in. Attach the plywood to the rabbeted area with double-faced tape. One edge of the plywood should butt against the shallow lip of the rabbet, and the ends of the plywood should overhang the board.

Now the board goes into the thickness planer with the plywood facedown. Set the planer for a light cut (1⁄64 in. to 1⁄32 in.). Then feed the two parts into the machine. Make additional passes as necessary.

Once the top face is smooth and flat, separate the plywood from the board and flip the board so the rabbet now faces up. Then use the thickness planer to make light passes as needed to remove the step and make a full-width cut. That’s all there is to it—straight, flat, and smooth.

Planer

1. Flip it, and use a spacer

2. Flip it once more and plane the step

Mike Wilson (ASC Construction) works wood in Redondo Beach, Calif. Tony Czuleger (IMC Construction) is based in Carson, Calif.

For the full article, download the PDF below:

Fine Woodworking Recommended Products

Bahco 6-Inch Card Scraper

The size and thickness are what matter here. A consistent performer, this Bahco scraper is found in many shops we visit.

Buy at Amazon

AnchorSeal Log and Lumber End-Grain Sealer

Good for both sealing the end grain of freshly cut logs and boards, this wax prevents end-grain checking and saves material

Buy at Amazon

Diablo ‘SandNet’ Sanding Discs

While Diablo’s SandNet disks perform similarly to conventional paper abrasives in terms of material removal and surface prep (with some exceptions at the lower grits), they make keeping your work surface and work area clean much easier, thanks to the great dust collection possible with them.

Buy at Amazon