Replies

1. 
   Knotscott | Feb 05, 2007 06:51pm | #1

   I saw him at the Buffalo wwing show in 2006 demoing the new Freud Fusion blade for Peachtree. 

1. 
   user-161113 | Feb 05, 2007 09:25pm | #2

   Thanks, Scotty.

   I would like to know two things:

   1. A way to contact Jerry Cole.

   2. Is another vendor selling his products?

   If you or anyone else can help me with this, would appreciate it.

   Billy B.

1. 
   Knotscott | Feb 06, 2007 03:07am | #5

   I don't think I have any of his info in my files, though I did do some business with him a couple of years ago. You might try contacting Peachtree and ask if they can put you in touch with him. If I can find my video with him in it, I'll check if there's a phone number...

1. 
   nikkiwood | Feb 06, 2007 03:42am | #6

   I assume you have been to his web site, where he lists an 800 number and an email address:http://www.in-lineindustries.com/double_dubby.htmDid you buy one of the Dubbys?********************************************************
   "It is what we learn after we think we know it all, that counts."

   John Wooden 1910-

1. 
   user-161113 | Feb 06, 2007 04:04am | #7

   This reply is for nikkiwood and Scotty primarily. But, I do appreciate the response of all, so this is for others as well.

   I guess I was a little too impatient. Having seen that the In-Line website had not been updated for quite some time, and, in addition, having been told by an AT&T recording that the numbers on the website had been disconnected, I reacted too soon.

   I later tried the order line number again. This time it worked. The young man that answered told me they had been having a problem with the phones this morning. May have had something to do with foul weather. Anyhow, he confirmed that Jerry is doing some work for Peachtree and that he is still in business with In-line products. Good. Jerry and wife are nice people and they have had good products.

   Yes, I have both the left and right Dubby which I bought many years ago. It is the old style with the wooden fence. I use the left-hand one all the time and occasionally I use the right-hand one. The left-hand one is getting kind of beat up. I have knocked it off my table saw and work bench a few times and have damaged the table portion. I am going to order a new one for the left-hand. I find these units very easy to use, very accurate in cutting 90 degree (square) end cuts and I depend on them very much for accurate angle cuts in other degrees. I will probably make a new table base for the old left-hand, restore it and give it to one of my brothers.

   Thanks people. I am relieved that apparently Jerry is well and still going. I will look for him at Peachtree booth in Houston, March 30 or 31. Best wishes to all.

   Billy B.

   Edited 2/5/2007 8:10 pm ET by Billy B.

2. 
   Knotscott | Feb 06, 2007 05:14am | #8

   Cool! Tell Jerry I said "hi"! (if he doesn't remember me, tell him I'm the guy who liked his demo of the Fusion blade... :D

2. 
   GregK | Feb 05, 2007 09:44pm | #3

   I saw him at the Novi WW show in December and he was still showing the Dubby.

1. 
   user-161113 | Feb 05, 2007 10:19pm | #4

   Thanks Greg. His web site for In-Line Industries has not been updated since 2004. I did not see him at the Dallas/Ft. Worth Show this past December. When you call the phones numbers shown in the web site, you get a recorded message saying the numbers have been disconnected. Right now, I am mainly concerned about his well-being. But, would also like to purchase one of his products.

   Thanks again,

   Billy B.